Description
Detailed information for: STUP-PP846A-PP846This page contains technical data sheet, documents library and links to offering related to this product. If you require any other information, please contact us using form located at the bottom of the page.Print… Print to Pdf… Data Sheet DownloadsSTUP-PP846A-PP846 General Information Product ID:STUP-PP846A-PP846 ABB Type Designation:PP846A StepUp Catalog Description:Operator Panel Categories Parts & Services » Control Systems » 800xA » Operations » Panel 800 » Panel 800 4.1 » Control System Accessories Parts & Services » Control Systems » 800xA » Operations » Panel 800 » Panel 800 5.0 » Control System Accessories Parts & Services » Control Systems » 800xA » Operations » Panel 800 » Panel 800 5.1 » Control System Accessories
1. The operator panel’s mounting clamps do not provide a secure grounding connection between the panel and the device cabinet. 2. Connect a 2.5 mm2 wire between the operator panel’s quick-connect plinth and the panel chassis. 3. Connect a 6 or 4 mm2 wire or grounding braid between the panel’s chassis and the closest grounding point on the door. 4. Connect a strong but short grounding braid between the door and the device cabinet. 5. Twist the cables onto the 24 V DC feed.
. A ferrite core suppresses disturbances to the 24 V feed. 2 turns around the ferrite core provide 4 times the suppression of 1 turn. 3 turns around the ferrite core provide 9 times the suppression of 1 turn. Ethernet Connection in the Panel 1. In some industrial units for Ethernet, the RJ45 contact’s shield is connected to the chassis via a capacitor. The grounding wires should be short and the conductor should have a large area. A long, thin grounding wire has a very high impedance (resistance) at high frequencies and will not guide disturbances to the ground. Multi-wire conductors are better than single wire conductors with the same area. A braided conductor wire with the same area is even better. The best is a short, thick grounding braid.
2. The operator panel’s Ethernet shield is directly connected to the chassis. Check whether the other Ethernet unit has its shield directly grounded or grounded via a capacitor. In many cases, connecting the shielded Ethernet cabling to the chassis at both ends is inappropriate. Hum or grounding loops can occur. Unshielded cabling may even result in fewer communication errors. A good solution may be to use a shielded Ethernet cable, but to connect the shield at one end only. 3. One option is to break the shield. 4. A more elegant method is to expand the shielded Ethernet cabling with a piece of unshielded Ethernet cable. 5. You can ground the shield via an external 0.1 uF/250 V plastic capacitor. This will connect the HF transients to the ground. To Achieve Better EMC Protection • Initially, use the original cabling from the supplier primarily. • Use shielded cables for RS232 communication. • Use twisted pair and shielded cabling for RS422 and RS485. • Use the cabling intended for the bus type; Ethernet, Profibus, CC-Link, CAN, Device Net etc. • Install and connect according to applicable specifications for the relevant bus standard. • Use shielded cabling for Ethernet, preferably with foil + braided shield. • D-sub covers should be shielded, and the shield should be connected to the cover 360 ° where the cable comes in.
With longer distances, there is a risk that the ground potential may be different. In that case, the shield should only be connected at one end. A good alternative is to connect the other end of the shield to the ground via a 0.1 uF/250 V plastic capacitor. Both ends are then connected to the ground in terms of HF, but only connected to the ground at one end in terms of LF, thus avoiding the 50 Hz grounding loops. • Use an EMC cable gland or regular plastic cable gland, remove the outer jacket and connect the shield to the installation plate with a 360 ° metal cable clamp.
[Service contact information]
Tel: 18030177759 (WeChat with the same number)
WhatsApp:+86 18030177759
QQ:2797820256
Address: Unit 2009, 20/F, 1733 Luling Road, Siming District, Xiamen
Shipment: EMS, DHL, UPS and FEDEX
Payment method: telegraphic transfer
Supply capacity: 30 sets/set per month
Price: the more orders, the lower the price
Delivery: inventory, delivery within 3 days
Address: Unit 2009, Innovation Center, 1733 Lvling Road, Siming District, Xiamen
① 24 hours email reply (12 hours);
③ For goods shipped to countries outside Asia, please contact the Seller.
Xiamen Xiongba E-commerce Co., Ltd. main brand;
ABB GE
bentley Woodward
FOXBORO
WESTINGHOUSE Schneider
AB Motorola
GE EMERSON
YOKOGAWA Honeywell
EPRO ICS TRIPLEX
It is mainly used as the card driver of the spare parts module for the four major systems of PLC DCS robot servo
1. For inventory items, we will ship them to you within 3 days after receiving payment
2. We can ship goods to all parts of the world through DHL, UPS, FEDEX, TNT and EMS.
3. If you have a freight forwarder, please inform us before shipment.
4. We will pack the parts in strong boxes. If you have any special needs, please inform us.
5. We usually deliver the goods before 4:30 p.m., and we will send the tracking number to you after delivery. It takes 7-15 days to receive the package.
6. Please email us after receiving the package.
7. Please include all information when inquiring about the transportation cost, otherwise it will slow down the process.
8. What is your postal code?
9. If you have a company name, what is your company name?
10. If you have a telephone number and extension number, what is your telephone number?
11. We are the largest supplier in the region. We have great advantages in all kinds of popular and discontinued models. If you have models and spare parts that you can’t find here, you can boldly send me to help you check!!!!!!
12. We only make spare parts for high-voltage and medium-high voltage products!!!!!!!
Model recommendation:
Reviews
There are no reviews yet.