Description
The IS421UCSBH4A-UCSB controller module is in stock and will be shipped on the same day.
The IS421UCSBH4A-UCSB controller module is in an unused and rebuilt state.
If you need the best discount on IS421UCSBH4A-UCSB controller module, please contact us and we will reply to you within 24 hours.
IS421UCSBH4A Other names:
Control unit IS421UCSBH4A
IS421UCSBH4A Analog Input Output Controller
Communication controller IS421UCSBH4A
Product Description
The IS421UCSBH4A controller is the first UCSB controller in the Mark VIe Control Safety System series manufactured by General Electric. This controller is similar to the UCSC controller, although the hardware is different, the software required to operate this controller is almost the same. According to the GEH-6725 Mark VIe and Mark VIeS, Control Equipment Hazardous Area Use Guidelines, the IS421UCSBH4A controller is labeled as a Mark VIe, LS2100e, and EX2100e controller. The controller also uses a specific microprocessor, and the microprocessor installed in the device is a 600 MHz EP80579 Intel processor.
On page 22 of the GEH-6725 user manual, there is a small table indicating the electrical/power ratings required to power IS421UCSBH4A. The ratings are as follows: minimum voltage is 18 volts DC, maximum DC is 30 volts, and nominal power ratings are 24 volts and 28 volts DC. The maximum current rating used by this device is 1.5 ADC.
When installing, installing the IS421UCSBH4A controller in hazardous and non hazardous locations requires multiple certifications. For example, when installed in ATEX Zone 2, IIC group, the required certification is UL DEMKO 12 ATEX 1114875X. All certifications for controllers installed in Class I, Zone 2, Group IIC, non hazardous and Class I, Zone 2, Groups A, B, C, and D are the same, and the certification requirements for these locations are UL E207685.
IS421UCSBH4A is a UCSB controller module developed by GE. The UCSB controller is an independent computer that can execute application specific control system logic. Unlike traditional controllers, UCSB controllers do not host any application I/O. In addition, all I/O networks are connected to each controller, providing it with all input data. If the controller loses power due to maintenance or repair, the hardware and software architecture ensures that no application input points are lost.
Surgery
The controller is pre installed with specialized software. It can run steps or blocks. No need to restart the system to make minor changes to the control software online.
The IEEE 1588 protocol is used to synchronize the clock of I/O packets and controllers to within 100 microseconds through R, S, and T IONets. External data is transmitted to or from the control system database of the controller through R, S, and T IONets. This includes the process inputs and outputs of the I/O module.
This also includes the following in the dual system:
Specify the internal state values and initialization information of the controller
Status and synchronization information from two controllers
This also includes the following in Triple Modular Redundancy (TMR) systems:
Internal state values for voting and status, as well as synchronization information from all three controllers
Data from the specified controller for initialization
IS421UCSBH4A Advantages
The UCSB controller has the following advantages:
Single module
Built in power supply
No need for jumper settings
No battery
No fans
Smaller panel size
Flash memory can be easily updated
The UCSB controller is installed in the panel and communicates with the I/O package through the onboard I/O network (IONet) interface. IONet is a dedicated Ethernet that only supports Mark controlled I/O modules and controllers.
Features
Microprocessor: 600 MHz Intel EP80579
Memory: 256 MB DDR2 SDRAM with Error Correction Code (ECC), SRAM supported by flash memory, NAND flash memory size of 2 GB
Operating system: QNX Neutrino
Weight: 2.4 pounds
Installation
The UCSB controller is installed in a separate module that is directly connected to the panel metal plate.
The UCSB controller should be installed on a heat sink panel that allows vertical air circulation.
Comment on IS421UCSBH4A
Internal review
The IS421UCSBH4A controller is a highly reliable and versatile module due to its long lifespan and compatibility with EX2100e, LS2100e, and Mark VI systems. Its failure rate is very low and is related to most defects, which can be repaired
Frequently asked questions
What is IS421UCSBH4A?
IS421UCSBH4Ais a UCSB controller module developed by GE
What is the weight of this component?
This component weighs approximately 2.4 pounds
How to obtain the spare parts for this product?
Please call the Industrial Control Sales Consultant: Carrey
WhatsApp:+86 18030177759
All products on this website are special products, and market prices have been fluctuating,
The specific customer service quotation shall prevail, as the product is a new product and the price is not genuine,
Please confirm the model, product, price, and other detailed information with customer service before placing an order. The website has been used,
The new one is for sale, please contact customer service to communicate.
Warehouse discount product recommendation:
IS420UCSBH1A
IS420UCSBH1A-UCSB
IS420UCSCH1A-UCSC
IS420YDIAS1B
IS420PUAAH1A
IS420UCSCH2A-C-V0.1-A
IS420UCSCH1B
IS220YDIAS1A
IS200AEPAH1BKE
IS200TDBSH2ACC
IS220PRTDH1A
IS220PRTDH1A
IS220PSCAH1A
IS220PVIBH1A
IS200JPDEG1A
IS200VPROH1BEF
IS200VPROH2B
More……
Reviews
There are no reviews yet.