SHINKAWA Shaft Vibration Monitor VM-5Z4

SHINKAWA Shaft Vibration Monitor VM-5Z4

Description


  Many products have not yet been launched, please contact us for more products

  If the product model does not match the displayed image, the model shall prevail. Please contact us for specific product images, and we will arrange for photos to be taken in the warehouse for confirmation

  We have 16 shared warehouses worldwide, so sometimes it may take several hours to accurately return to you. We apologize for any inconvenience caused. Of course, we will respond to your concerns as soon as possible.


The VM-5 Series monitors are designed to comply with American Petroleum Institute (APl) Standard 670 for rotating machinery. Available in 8-slot and 10-slot rack-mount types and stand-alone types with built-in power supplies, these monitors are flexible to cope with any system design from small and medium-sized rotating machinery to TSl (Turbine Monitoring Instrumentation) for large turbines used in generators. In addition, these are designed to be user-friendly so that all operations and inspections can be performed from the front of the monitor without stopping the operation. They also include all the functions required to monitor a variety of variables of rotating machinery from displacement and vibration to zero speed, enabling any system design corresponding to the type and size of machinery. System Configuration

The VM-5 Series has two instrument racks – the rack-mount types VM-5H3 (8-slot) and VM-5W1 (10-slot), and a stand-alone type with built-in power supply (VM-5G).

  Installation

For the rack-mount type, mount the monitor unit to the front panel and the associated module unit to the rear panel. The communication unit and power supply unit are also mounted on the rear panel. The single-unit frame (VM-5G) comes with pre-installed relay modules, so there is no need to install additional modular units.


  MONITOR UNIT

VM-5K Dual Vibration Monitor

VM-55 Vibration Monitor

VM-5U Dual Seismic Monitor

VM-5B Dual Acceleration Monitor

VM-5M Dual Path Monitor

VM-5C Eccentricity Monitor

VM-5T Dual Thrust Monitor

VM-5D Dual Differential Expansion Monitor

VM-5N Ramp Differential Expansion Monitor

VM-5L Complementary Input DifferentialExpansion Monitor

VM-5J Case Expansion/Complementary Differential Expansion Monitor

VM-5E Dual Case Expansion Monitor

VM-5A Dual Valve Position Monitor

VM-5S Dual Tachometer

VM-5Q Reverse Rotation Monitor

VM-5R Tachometer

VM-51 Rod Drop Monitor

VM-52 Bottom Hold Monitor

VM-5F Dual Temperature Monitor

VM-5Y Relay Module Unit

VM-5X Interface Unit

VM-5P3 Phase marker Unit

VM-53 Dual Communication Unit

VM-5Z Power Supply Unit

VM-5Z0 Power Supply BackupModule Unit

VM-5 Series


  Monitor Unit

The VM-5 Series monitor unit is mounted on the front panel of each instrument rack. The LCD display, each display light, and BNC output terminals are neatly mounted on the slim panel. (Display styles vary.) Bar graphs and digital measurement value indications are used on the display for easy reading. Bar graphs are also used to indicate danger and alarms. These are also displayed clearly. When an alarm occurs, each alarm LED lights up, providing easy visual confirmation.


  General Specifications

Recorder Output

Voltage or current output is proportional to the monitoring range.

1 to 5VDC (output impedance: 2502)

4 to 20mADC (maximum load resistance: 500) Options: 0 to -10VDC, 0 to 10VDC, 0 to -5VDC, 0 to 5VDC (output impedance: 1002) Output points: 2 points

Monitor output (from front panel, rear panel) Input signal is output through a buffer amplifier.

Operating temperature: 0 to 65°C

Output impedance: Approx. 100Ω


  VM-5 SYSTEM MONITOR UNITS

VM-5K Dual Vibration Monitor

VM-55 Vibration Monitor

VM-5U Dual Seismic Monitor

VM-5B Dual Acceleration Monitor

VM-5M Dual Path Monitor

VM-5C Eccentricity Monitor

VM-5T Dual Thrust Monitor

VM-5D Dual Differential Expansion Monitor

VM-5N Ramp Differential Expansion Monitor

VM-5L Complementary Input Differential Expansion Monitor

VM-5J Case Expansion/Complementary Differential Expansion Monitor

VM-5E Dual Case Expansion Monitor

VM-5A Dual Valve Position Monitor

VM-5S Dual Tachometer

VM-5Q Reverse Rotation Monitor

VM-5R Tachometer

VM-5F Dual Temperature Monitor

VM-51 Rod Drop Monitor

VM-52 Bottom Hold Monitor


  VM-5K Dual Vibration Monitor

Inputs signals from the FK/VK Series Vibration

Transducers corresponding to 2 channels.

Simultaneously provides 2 points of shaft

vibration monitoring within one unit.


  VM-5U Dual Seismic Monitor

Inputs signals from the CV Series Velocity

Transducer corresponding to 2 channels.


  VM-55 Vibration Monitor

Simultaneously monitors both relative and absolute

vibrations or relative and seismic vibrations


  VM-5B Dual Acceleration Monitor

Inputs signals form the CA Series Acceleration

Transducer corresponding to 2 channels.


  VM-5M Dual Path Monitor

Simultaneously monitors the velocity/acceleration and displacement/velocity vibration of rotating machinery detected by CV Series Velocity

Transducer or CA Series Acceleration Transducer.

Detects machine failures early on and informs the operator of these failures.


  VM-5C Eccentricity Monitor

Monitors the shaft deflection (eccentricity pk-pk) of the turbine rotor at machine start-up and turning.


  VM-5T Dual Thrust Monitor

Monitors the shaft position of rotating machinery.

Inputs thrust displacement signals from the FK/VK Series Transducers and monitors shaft position.


  VM-5D Dual Differential Expansion Monitor

Measures the differential expansion caused by thermal expansion of the rotor and casing. Inputs the expansion of the rotor away from the thrust bearing detected with the VK Series Transducer to measure the differential expansion.


  VM-5L Complementary input Differential Expansion Monitor

Measures the differential expansion caused by the thermal expansion of the rotor and casing. Receives input from two sensors installed in a complementary arrangement and can measure the differential expansion to twice the sensor range.


  VM-5E Dual Case Expansion Monitor

Inputs the casing expansion signal from the LS Series LVDT Linear Variable Differential Transformer and displays them on LCDs.


  VM-5N Ramp Differential Expansion Monitor

Measures the differential expansion caused by the thermal expansion of the rotor and casing. Inputs the expansion of the rotor detected by the VK Series

Transducers installed on the rotor ramp away from the thrust bearing, then outputs the computed differential expansion, thereby eliminating the measurement error resulting from rotor lifting caused by oil film, etc.


  VM-5J Case Expansion /Complementary Differential Expansion Monitor

Measures differential thermal expansion between the rotor and case of rotating machinery. Accepts the output of the VM-5L Complementary Input Differential

Expansion Monitor and the case expansion signal from the LVDT, performs compensation, and computes the differential expansion value.


  VM-5A Dual Valve Position Monitor

Inputs the valve position signal from the LS Series

LVDT linear Variable Differential Transformer and displays them on LCDs.


  VM-5S Dual Tachometer

Monitors the rotor speed of the shaft and zero-speed.


  VM-5Q Reverse Rotation Monitor

Provides detection of reverse revolutions, indicating peak reverse speed values that have occurred.


  VM-5R Tachometer

Monitors the rotor speed and rotor acceleration of the shaft, and can set speed comparison values to the rotor velocity or rotor acceleration independently.


  VM-5F Dual Temperature Monitor

This monitor is designed to monitor the temperature of rotating machinery. lt inputs signals from grounded/non-grounded thermocouples, or 3-wire/4-wire RTDs and displays them on LCDs.


  VM-51 Rod Drop Monitor

Monitors the gap between the piston rod set as the target and the sensing surface of the sensor for rod drop measurement (FK/VK) so as to synchronize with the phase marker, and then converts the gap thus measured to the amount of rider ring abrasion.


  VM-52 Bottom Hold Monitor

Monitors the gap between the piston set as the target and the sensing surface of the sensor for rider ring abrasion measurement to obtain the amount of abrasion.


  V-5 SERIES MODULE UNIT

This unit is available in several different styles – Relay, Interface. Communication, Phase Marker, Power Supply unit, etc., and provides high functioning and reliability. To use, install into the front or rear panel of the instrument rack (VM-5H3 Instrument Rack or VM-5W1 Dual Power Supply Instrument Rack).


  VM-5Y1,2,3 Relay Module Unit

These units are designed for use with VM-5 Series Monitors. Mounted on the rear panel of the VM-5H3 or VM-5W1 Instrument Rack, they output contact signals such as input abnormal, alert and danger alarms for sequence control. Using 10mm-pitch two column large-sized terminal block, there is no complicated wiring involved.


  VM-5Y4.5.6 Relay Module Unit

These units are the connector type Relay Module. Mounted on the rear panel of the VM-5H3 or VM-5W1 Instrument Rack, VM-5Y4 and 6 can output the recorder output and alarm output signal and VM-5Y5 can output the buffer output and alarm output signal through the D-sub connector.

They also output contact signals of the sequence control for input abnormal, alert and danger alarms from the terminal block. An arc suppressor (optional) absorbs the arc discharge between contacts to prevent damage to the internal circuits.


  VM-5Y7 Relay Module Unit

Designed for use with the VM-5F Dual Temperature Monitor. Mounted on the rear panel of the VM-5H3 or VM-5W1 instrument Rack, it outputs a contact siqnal of sequence control for alert and danger alarms.


  VM-5X1,2,3 Interface Unit

Distribute and output the recorder output from the VM-5 Series Monitor Units. They also output analog signals distributed from the VM-5X2,3 interface Unit l/0 module mounted on the rear panel of the VM-5H3 or VM-5W1 Instrument Rack. Using a 10mm-pitch two column large-sized terminal block, there is no complicated wiring (VM-5X2). The VM-5X3

Interface Unit l/0 Module (connector type) outputs recorder output from the D-sub connector.


  VM-5P3 Phase Marker Unit

Accommodated in a VM-5H3 or VM-5W1 Instrument Rack, these units process phasemarker signals, and provide OK alarm contact output and internal power supply voltagefailure detection.


  VM-53 Dual Communication Unit

This unit has two independent serial ports. While inserted in a relay module slot of the VM-5H3 or VM-5W1 Instrument Rack, it collects static data in the rack by the Modbus protocol and then sends it to an external host computer. In addition, as this unit can be daisy chain-connected, it enables data collection from two or more racks.


  VM-5Z1,2,3,4 Power Supply Unit

Provides DC power to each VM-5 Series unit mounted in the same instrument rack. A fault in the power supply is indicated by lighting of the power supply OK lamp and alarm contact output.


  VM-5Z0 Power Supply Backup Module Unit

Backs up the DC power supplied to each VM-5 Series units mounted in the VM-5H3 or VM-5W1 Instrument Rack, at the time of an instantaneous electric power failure.


  VM-5W1 Dual Power Supply Instrument Rack

Designed to accommodate the VM-5Z Power Supply Unit. The VM-5 Series Monitor and VM-5Y Relay Module Unit mounts on a standard panel. This rack can accommodate one(1)VM-5P Communication/Phase Marker Unit, and up to ten(10)V-5 Series Monitors with a VM-5Y Relay Module for each unit. A duplexes power supply is obtained by mounting two VM-5Z power Supply Unit.


  VM-5H3 Instrument Rack

Accommodates the VM-5P Communication/Phase Marker Unit and VM-5 Series monitors. This rack can accommodate one(1)VM-5P and up to eight (8)VM-5 Series Monitors with VM-5Y Relay Module Unit and VM-5Z Power Supply Unit for every unit accommodated.


  VM-5G0.1,2 Single Unit Instrument Rack

This type of instrument rack consists of a power supply for each VM-5 Series Monitor (except the VM-5 Communication/Phase

Marker Unit and VM-5F Temperature Monitor Unit), SPDT (DAN. 1, DAN.2,ALE.1,ALE.2)four(4) point relay and OK relay.


  All products on this website are special products, and market prices have been fluctuating,

  Please refer to the customer service quotation for details, as the product is new and the price is not genuine,

  Please confirm the model, product, price, and other detailed information with customer service before placing an order. The website has been used,

  The new one is for sale, please contact customer service for further communication.


Related product recommendations:
SHINKAWA VM-3E2
SHINKAWA VM-5T
SHINKAWA VM-5k
STEIN SOHN A056
STEIN SOHN 961080 A040.4-1111A
STEIN SOHN 96-1079 A004.5.1-31111
SPOHN+BURKHARDT 2082823-1-2
SPM INSTRUMENT DMM-10 SHOCK
SPM INSTRUMENT BMM-21
SPJETRI NGJ-1 MULTI FUNCTION
More……

Reviews

There are no reviews yet.

Be the first to review “SHINKAWA Shaft Vibration Monitor VM-5Z4”

Your email address will not be published. Required fields are marked *