Description
IS420UCSBH4A – UCSB Controller Module is available in stock which ships the same day.
IS420UCSBH4A – UCSB Controller Module comes in UNUSED as well as REBUILT condition.
To avail our best deals for IS420UCSBH4A – UCSB Controller Module, contact us and we will get back to you within 24 hours.
IS420UCSBH4A Other names:
Switch IS420UCSBH4A
Control system module IS420UCSBH4A
Editable controller IS420UCSBH4A
Product Description
Controller IS420UCSBH4A is another UCSB controller produced by General Electric for the Mark VIe series. According to the description, the controller can operate on the EX2100e, LS2100e, and Mark VIe series running on the 1066 MHz EP80579 Intel processor. The EP80579 processor is used to assist applications that require high reliability and speed. This model is similar to previous UCSB controllers, except for the processors mentioned above, which all use the same processor type but run on different MHz.
The IS420UCSBH4A controller is similar to the UCSC controllers in the Mark VIe series. The difference between these controllers lies in their hardware, but they do have some similarities in terms of controller advantages. Some advantages of the controller are that it is a single module and has flash memory, which can be easily updated according to the needs of users. The location and certification required to operate this controller are the same as the previous model. The controller can be used in hazardous and non hazardous areas and has UL E207685 and UL DEMKO 12 ATEX 1114875X certifications. All information about the location and required authentication can be obtained from the GEH-6725 Mark VIe/VIeS Control Equipment HazLoc Instruction Guide on page 112.
The UCSB Controllers offer the Following Advantages:
Single module
Built-in power supply
No jumper settings required
No battery
No fan (UCSBSIA, UCSBHIA, UCSBH4A)
Dual-redundant fans with IS420UCSBH3A
Smaller panel footprint
Flash memory can be conveniently updated
UCSB INSTALLATION:
A single module that installs directly to the sheet metal of the panel contains the controller. The dimensions for the module envelope and mounting are shown in the diagrams below. Every measurement is in inches. The UCSB must be attached to the panel as depicted, with the vertical airflow through the fins remaining unhindered.
UCSB SOFTWARE AND COMMUNICATION:
Software customized for the controller’s use is installed. Rungs or blocks can be run by it. Without needing to restart, small changes to the control software can be done online. The clocks of the 1/O packs and controllers are synchronized to within 100 microseconds using the IEEE 1588 protocol via the R, S, and T IONets. Through the R, S, and T IONets, external data is sent to and received from the control system database in the controller. This comprises the 1/0 modules’ process inputs and outputs.
Additionally, in a dual system, these are:
1. Data on initialization and internal state variables from the selected controller
2. Information on the synchronization and status of both controllers
This also covers the following in a triple modular redundant (TMR) system:
Information on synchronization from all three controllers, internal state values for voting, and status
Initialization data from the chosen controller
UCSB BOOT LED:
In the absence of a mistake, the boot LED remains on throughout the boot process. The LED will blink once per second (Hz) if an error is found. The LED blinks for 500 milliseconds, then goes off. The LED stays off for three seconds after the flashing phase. Flash count reveals failed condition.
The boot LED flashes continuously at a Hz rate if the flash image is genuine but the runtime firmware has not yet been loaded. The firmware loads and the boot LED goes off. Use the ToolboxST app to find out why the controller is blocked if it won’t connect online. After receiving an IP address, ToolboxSTplication configures itself over Ethernet.
FREQUENTLY ASKED QUESTIONS:
What is IS420UCSBH4A?
It’s a high-performance UCSB Controller Module with a 1066 MHz Intel EP80579 microprocessor.
What is a UCSB Controller?
The UCSB controller is a single-board, stand-alone processor with scalable processing power. There are no batteries or jumper settings required because it has a built-in power supply.
What is the application of the module?
The module allows interoperable redundant configurations that incorporate many platform types into a single redundant set.
What is the operating temperature of the component?
The operating temperature ranges from 22 to 149 degrees Fahrenheit.
Reviews For IS420UCSBH4A
The IS420UCSBH4A controller can be used in this Mark VIe control system as well as EX2100e and LS2100e system applications. This controller can also be used in high-speed applications.
All products on this website are special products, and market prices have been fluctuating,
The specific customer service quotation shall prevail, as the product is a new one and the traps are not real,
Please confirm the model, product, price, and other detailed information with customer service before placing an order. The website has been used,
New for sale, please contact the website( https://www.weikunfadacai1.com/ )Customer service communication.
Model recommendation:
GE IS420ESWBH3A
IS420ESWBH3A-C GE
IS420ESWBESWB GE
IS420ESWAH1A GE
IS420ESWBH3A-ESWA GE
IS420ESWAH2A GE
IS420ESWBH3A GE
IS420ESWBH3AE GE
IS420ESWAH3A GE
GE IS420ESWBH1A
NI SCXI-1000
more……
admin –
Controller IS420UCSBH4A is another UCSB controller produced by General Electric for the Mark VIe series. According to the description, the controller can operate on the EX2100e, LS2100e, and Mark VIe series running on the 1066 MHz EP80579 Intel processor. The EP80579 processor is used to assist applications that require high reliability and speed. This model is similar to previous UCSB controllers, except for the processors mentioned above, which all use the same processor type but run on different MHz.