GE IS420UCSBH1A-UCSB Controller Module for sale online

Sale!

GE IS420UCSBH1A-UCSB Controller Module for sale online

¥6,521.00

Description


         IS420UCSBH1A – UCSB Controller Module is available in stock which ships the same day.

  IS420UCSBH1A – UCSB Controller Module comes in UNUSED as well as REBUILT condition.

  To avail our best deals for IS420UCSBH1A – UCSB Controller Module, contact us and we will get back to you within 24 hours.


  General Electric’s Mark VIe Controller IS420UCSBH1A is similar to the UCSC Controller and all of the same general information can be applied to the UCSB model. The IS420UCSBH1A model is typically a compact stand-alone controller used to help with controller logic.

        IS420UCSBH1A-UCSBOther names:

  Switch IS420UCSBH1A-UCSB

  Control system module IS420UCSBH1A-UCSB

  Editable controller IS420UCSBH1A-UCSB


  Product Description

The IS420UCSBH1A controller is the first of the UCSB controllers manufactured by General Electric as part of the Mark VIe Control Safety System Series. This controller is similar to the UCSC controller and while it does not have the same hardware the software needed to operate this controller is nearly identical. According to the GEH-6725 Mark VIe and Mark VIeS, Controls Equipment HazLoc Instruction Guide the IS420UCSBH1A controller is labeled as a Mark VIe, LS2100e, and EX2100e controller. There is also a specific microprocessor used with this controller, the microprocessor installed in this device is the 600 MHz EP80579 Intel Processor.

On page twenty-two of the GEH-6725 Instruction Guide, there is a small table that labels the electrical/power supply ratings needed to power the IS420UCSBH1A, the ratings are as follows, a minimum voltage of eighteen direct currents, with a maximum of thirty volts of direct current, the nominal power rating is twenty-four and twenty-eight volts of direct current. The maximum current rating used with this device is 1.5 ADC.

When being mounted there are several certifications that are required to mount the IS420UCSBH1A controller in hazardous and non-hazardous locations alike. For example, when mounted in ATEX Zone 2, Group IIC, the certification needed is UL DEMKO 12 ATEX 1114875X. All certifications regarding the controller being mounted in Class I, Zone 2, Group IIC, non-hazardous, and Class I, Division 2, Groups, A, B, C, and D are the same, the certification requirements for these locations are UL E207685.

IS420UCSBH4A(2)
  IS420UCSBH1A is a UCSB Controller Module developed by GE. UCSB controllers are self-contained computers that execute application-specific control system logic. The UCSB controller does not host any application I/O, unlike traditional controllers that do. Furthermore, all I/O networks are connected to each controller, providing it with all input data. If a controller is powered down for maintenance or repair, the hardware and software architecture ensures that no single point of application input is lost.

IS420UCSBH4A(2)


Operation

The controller is pre-loaded with application-specific software. It is capable of running rungs or blocks. Minor changes to the control software can be made online without restarting the system.

The IEEE 1588 protocol is used to synchronize the clocks of the I/O packs and controllers to within 100 microseconds via the R, S, and T IONets. External data is transferred to and from the controller’s control system database via the R, S, and T IONets. Process inputs and outputs to I/O modules are included.


  This also includes the following in a dual system:

        The designated controller’s internal state values and initialization information

  The status and synchronization information from both controllers


  This also includes the following in a Triple Modular Redundant (TMR) system:

         Internal state values for voting and status, as well as synchronization information from all three controllers

  Data from the designated controller for initialization

  IS420UCSBH1A Advantages


  The following benefits are provided by UCSB controllers:

          Single module

  Built-in power supply

  No need for jumper settings

  No battery

  No fan

  Smaller panel footprint


  Flash memory can be easily updated

  The UCSB controller is installed in a panel and communicates with I/O packs via on-board I/O network (IONet) interfaces. IONet is a private special-purpose Ethernet that supports only Mark controls I/O modules and controllers.


Characteristics

Microprocessor: 600 MHz Intel EP80579

Memory: 256 MB DDR2 SDRAM with error-correcting code (ECC), Flash-backed SRAM, NAND flash size is 2 gigabytes

Operating System: QNX Neutrino

Weight: 2.4 lbs


  Mounting and Installation

        The UCSB controller is housed in a single module that attaches to the panel sheet metal directly.

  The UCSB controller should be mounted to the panel unobstructed vertical air flow through the fins.


  Reviews For IS420UCSBH1A

  The IS420UCSBH1A Controller is a highly reliable and versatile module due to its longevity and compatibility with EX2100e, LS2100e, and Mark VI Systems. It has a low failure rate and is repairable as it relates to most defects


 Frequently Asked Questions

  What is IS420UCSBH1A?

  IS420UCSBH1A is a UCSB Controller Module developed by GE

  How much does the component weigh?

  The component weighs around 2.4 lbs


        All products on this website are special products, and market prices have been fluctuating,

  The specific customer service quotation shall prevail, as the product is a new one and the traps are not real,

  Please confirm the model, product, price, and other detailed information with customer service before placing an order. The website has been used,

  New for sale, please contact the website( https://www.weikunfadacai1.com/ )Customer service communication.


  More model recommendations:
IS420UCSCH1B GE
IS420ESWBH3A GE
IS420UCSBH1A GE
IS420ESWBH3A-C GE|
IS420YAICS1B GE
IS420UCSBS1A GE
IS420ESWBH2A GE
IS420ESWBESWB GE
IS420UCSCH2A-E-V0.1-A GE
IS420UCSBH3A-UCSB GE
AUTRONICA KD-20
AUTO MASKIN DCU305 A R2
AUTO MASKIN DCU305 R3
ABB SYNPOL D CMA-136 3DDE 300 416
ABB SYNPOL D 3DDE.300.400 CMA-120
ABB SYNPOL D 3DDE 300 400 CMA-12
ABB SYNPOL D 3DDE-300-400 CMA-12
ABB HIEE300698R1

Reviews

There are no reviews yet.

Be the first to review “GE IS420UCSBH1A-UCSB Controller Module for sale online”

Your email address will not be published. Required fields are marked *