Description
DS200PCCAG5ACB is available in stock which ships the same day
DS200PCCAG5ACB comes in UNUSED as well as REBUILT condition
To offer our best deals for DS200PCCAG5ACB, contact us and we will get back to you within 24 hours.
DS200PCCAG5ACB Other names:
PCB module DS200PCCAG5ACB
DS200PCCAG5ACB Input/Output Module
Analog module DS200PCCAG5ACB
The GE Speedtronic Mark V DS200PCCAG5ACB is a drive system power board, also known as a power connection card (PCCA). The DS200PCCAG5ACB is designed to connect the SCR power bridge to the control circuit of the driver. This is achieved by feeding the gate driver to the SCR bridge using a pulse transformer. As it has removed all buffers and relocated them to other locations in the system, this board is designated as a high horsepower PCCA and should be used with a high HP controller.
Hardware tips and specifications
The design purpose of DS200PCCAG5ACB is to act as an intermediary between the SCR power bridge and the driver control circuit in the Mark V series automation drive components. It uses a pulse transformer to feed the gate driver to the SCR bridge to achieve this. This circuit board is classified as a high horsepower PCCA and should be used with a high HP controller as it has eliminated all buffers and placed them in other locations of the system. In addition to having no buffers, this DS200PCCAG5ACB circuit board also eliminates the use of attenuation strings. There are 12 plug connectors on PCCA, which can be used to send forward and reverse gate pulse signals to the SCR bridge. It can also communicate with the power board using another plug connector. The power board that should be used with this system is a DCFB type board. This DS200PCCAG5ACB PCB should always be considered a static sensitive model, especially during installation or replacement. Although static electricity and contact with human skin may damage individual DS200PCCAG5ACB board hardware components, the base circuit board of this DS200PCCAG5ACB PCB is prone to accumulating potential user hazardous surface voltages, even after shutting down its main Mark V series automatic drive components. In order to facilitate and safely install the DS200PCCAG5ACB power connection card into its larger automatic drive, the base circuit board of this DS200PCCAG5ACB power connection card has been drilled in the factory, and each drill hole is surrounded by insulating material.
This PCCA also uses Leg reactors and fuses, and utilizes independent or common bus transformers. The extensive information provided is reminiscent of the grouping of the DS200PCCAG5ACB product in Group 5 of the General Electric Mark V series products; This grouping (marked by the position of the G5 series grouping label in the DS200PCCAG5ACB functional product number) also indicates that the maximum AX voltage of this DS200PCCAG5ACB power connection card is 1500 V rms, as well as its compatibility with J, K, and M-type Mark V series framework components. DS200PCCAG5ACB uses a total of 4 jumpers. These jumpers are marked as WP4, WP3, JP2, and JP1. The board is located directly behind the drive controller, which is located behind the power board. PCCA is fixed on the back of the board carrier through these two boards. There are 6 plastic brackets to fix it on the bracket. Before making any final purchase decision on this DS200PCCAG5ACB product, it is important to be aware that the performance specifications and dimensions originally indicated on this DS200PCCAG5ACB product have undoubtedly been affected by its acceptance of significant B-class functional product revisions.
This board does not have a buffer and does not use attenuation strings.
PCCA has 12 plug connectors that can be used to provide forward and reverse gate pulse signals to the SCR bridge. Another plug connector can be used to communicate with the power board.
This system should use DCFB type power board. This PCCA also uses leg reactors and fuses. It uses independent or shared bus transformers. There are a total of four jumper wires used in DS200PCCAG5ACB. WP4, WP3, JP2, and JP1 are the labels for these.
The board is located directly behind the drive control board, which in turn is located directly behind the power board. These two boards are used to secure PCCA to the back of the board carrier. PCCA is fixed in the carrier by six plastic brackets.
Frequently Asked Questions
What is the connection between pin 5PL-10 I/O of DS200PCCAG5ACB and DCFB board?
The P24 naming on the board identifies the 5PL-10 I/O connection between the DS200PCCAG5ACB and DCFB boards. This board connection represents a+24V output.
Is there an attenuation string on DS200PCCAG5ACB?
No, there are no attenuation lines and buffers on the board. Because DS200PCCAG5ACB is a G5 board group, this is indeed the case. There are no attenuation lines or buffers in the G5 and G6 PCCA groups, including the DS200PCCAG5ACB.
How many jumpers are there in DS200PCCAG5ACB?
There are four jumper wires on the circuit board. JP1, JP2, WP3, and WP4 are jumpers that control the system voltage.
What is the pin 5PL-10 I/O connection between DS200PCCAG5ACB and DCFB board?
The 5PL-10 I/O connection between DS200PCCAG5ACB and DCFB board is identified by the named P24 on DS200PCCAG5ACB. This connection on DS200PCCAG5ACB describes the+24V output of DS200PCCAG5ACB.
Does DS200PCCAG5ACB have attenuation strings?
No, DS200PCCAG5ACB does not have attenuation lines, and DS200PCCAG5ACB also does not have any buffers. This is because DS200PCCAG5ACB is a G5 board group. The G5 and G6 PCCA groups, including DS200PCCAG5ACB, do not have attenuation lines or buffers.
How many jumpers are there in DS200PCCAG5ACB?
DS200PCCAG5ACB has a 4-wire jumper. The jumper wires for DS200PCCAG5ACB are JP1, JP2, WP3, and WP4. The jumper on DS200PCCAG5ACB is used to select the system voltage.
All products on this website are special products, and market prices have been fluctuating,
Please refer to the customer service quotation for details, as the product is new and the price is not genuine,
Please confirm the model, product, price, and other detailed information with customer service before placing an order. The website has been used,
The new one is for sale, please contact customer service for further communication.
Related product recommendations:
DS200FSAAG1ABA
DS200SHVMG1AFE
DS200LDCCH1AKA
DS200SI0CG1A6A
DS200SHVMG1AGE
DS200SI0CG1AEA
DS200PCCAG1ACB
DS200UCPBG6AFB
DS200TCQCG1BJF
DS200DCFBG1BLC
IS200WEORG1A
IS200ESELH1A
IS200AEPGG1AAA
IS200TSVCH2AED
IS200EPMCH1
IS200JPDGH1A
IS200ECTBG1ADE
IS200WETAH1AGC
IS200EXHSG3REC
IS200JPDSG1A
more……
admin –
The design purpose of DS200PCCAG5ACB is to act as an intermediary between the SCR power bridge and the driver control circuit in the Mark V series automation drive components. It uses a pulse transformer to feed the gate driver to the SCR bridge to achieve this. This circuit board is classified as a high horsepower PCCA and should be used with a high HP controller as it has eliminated all buffers and placed them in other locations of the system. In addition to having no buffers, this DS200PCCAG5ACB circuit board also eliminates the use of attenuation strings. There are 12 plug connectors on PCCA, which can be used to send forward and reverse gate pulse signals to the SCR bridge. It can also communicate with the power board using another plug connector. The power board that should be used with this system is a DCFB type board. This DS200PCCAG5ACB PCB should always be considered a static sensitive model, especially during installation or replacement. Although static electricity and contact with human skin may damage individual DS200PCCAG5ACB board hardware components, the base circuit board of this DS200PCCAG5ACB PCB is prone to accumulating potential user hazardous surface voltages, even after shutting down its main Mark V series automatic drive components. In order to facilitate and safely install the DS200PCCAG5ACB power connection card into its larger automatic drive, the base circuit board of this DS200PCCAG5ACB power connection card has been drilled in the factory, and each drill hole is surrounded by insulating material.