Description
5466-1001 – Digital Controller Power Supply Module is available in stock which ships the same day.
5466-1001 – Digital Controller Power Supply Module comes in UNUSED as well as REBUILT condition.
To avail our best deals for 5466-1001 – Digital Controller Power Supply Module, contact us and we will get back to you within 24 hours.
Woodward MicroNet Digital Controller Power Supply Module 5466-1001 has a power input of 110 VAC/125 VDC and is also a MicroNet-Plus unit. This unit has LVD, EMC, and ATEX certifications. Information on the 5466-1001 can be found in the 26166V2 manual.
| Weight : | 22 kg in Chassis | Standards : | CSA, ATEX, LVD, EMC, ABS, and DNV |
| Sound Level : | < 70 dBA | Series : | MicroNet Digital Controllers |
| Part Number | 5466-1001 | Model | MicroNet-Plus Power Supply |
Functional Description
5466-1001 is a Digital Controller Power Supply Module developed by Woodward. When power supplies are in use, current sharing circuitry balances the load to reduce heat and improve power supply reliability. If one of the power supplies fails, this feature allows for the power supplies to be replaced while the control is still running. Power supply has four LEDs that indicate the health of the power supply (OK, Input Fault, Overtemperature, and Power Supply Fault).
5466-1001 Other names:
Input/output modules 5466-1001
5466-1001 analog module
Information modules 5466-1001
Features
The power requirements for each system are determined by the number and type of modules supplied. Size the input power source for a system with a single I/O chassis according to the rating of the MicroNet TMR main power supply to which the source is connected.
When using redundant supplies, do not size the supply mains for the sum of the MicroNet TMR main power supply ratings. When MicroNetTM supplies are installed in the same chassis, they are redundant.
Redundant supplies share the load equally, but each must be able to handle the full load if one of the units fails. It is not recommended to connect both MicroNet main power supplies of a redundant pair to a single source, as failure of that source would disable the system. Multiple chassis systems that use MicroNet TMR main power supplies may have power supplies of the same model in different chassis that are connected to the same source.
Woodward model 5466-1001 is a power supply module part of the MicroNet Digital Controller series. There are two types of controllers, MicroNet Simplex and MicroNet-Plus, this specific unit is a MicroNet-Plus controller. When the controller has been connected to the chassis it will operate on a two-slot power supply at one-hundred-ten volts of actuating current or one-hundred twenty-five volts of direct current. This unit is also a safety integrity level (SIL) approved MicroNet Plus unit.
As a power supply module, the 5466-1001 must have the power supply disconnected when being installed. When a new power supply unit is being installed the circuit board edges must be aligned in the card guides, when the motherboard and slot units make contact it means that the board has been connected properly. There are four LEDs on the front faceplate of this unit, an overtemperature LED, an input, and a power supply fault, as well as an OK LED. The LEDs will light up solid or flash when a fault has been detected.
Power Supply Fault LED
When one of the supply’s four power converters fails, this red LED illuminates. If this LED is illuminated, look for a short circuit on any external devices that are connected to the control’s power supply. The supply will resume normal operation once the short circuit has been removed.
If no short circuits are found, reset the supply by turning off the power for one minute. If the power supply is still not working after restoring input power, make sure it is properly seated to the motherboard connector. If the supply is properly seated but not working, it should be replaced.
Frequently Asked Questions
What is 5466-1001?
It is Digital Controller Power Supply Module developed by Woodward.
How should the input power source be sized for a single I/O chassis in the system?
The input power source for a single I/O chassis should be sized according to the rating of the MicroNet TMR main power supply it is connected to.
What is the significance of redundant power supplies?
Redundant power supplies in a MicroNet system share the load equally between them. However, each power supply must be capable of providing full load in case one of the units becomes disabled.
Can I use the MicroNet TMR main power supply input ratings as a reference for sizing my system’s power source?
Yes, if the cabinet system nameplate does not indicate specific power requirements, you can use the input ratings of the MicroNet TMR main power supply as a reference for sizing the power source.
Reviews For 5466-1001
The 5466-1001 model is another SIL-approved unit but operates on a different power input than it’s predecessor, if you need a model to replace this one please be sure that you are getting the same unit, another unit being used can cause potential errors.
All products on this website are special products, and market prices have been fluctuating,
The specific customer service quotation shall prevail, as the product is a new one and the traps are not real,
Please confirm the model, product, price, and other detailed information with customer service before placing an order. The website has been used,
New for sale, please contact the website https://www.weikunfadacai1.com/ Customer service communication.
Warehouse module model recommendation：
KUC720AE101 3BHB000652R0101
5501-467
3BHE014185R0002
UUD148AE02 3BHE014185R0002
1336-BDB-SP45D
BSA-101-7212-142.0008-BSA101
WEEK-35-97-SSV-7212-242.0000
MVME162-212
S21260-SRS
PFTL 101AE-1.0 3BSE004212R1
3BSE004212R1
5466-017
5466-258
5466-3321
5466-1001
5466-409
5466-355
5466-315
Reviews
There are no reviews yet.