Description

　Annunciators:Indicators for the primary IDE interface activity, board status, power good and a blue LED for hot swap are provided on the front panel. In addition, two indicators for the Ethernet adapter activity are located on each RJ45 network connector.

Thermal Management: The VMICPCI-7806 utilizes a passive heat sink that relies on forced air cooling within the equipment rack at the specified flow rate. Please refer to the environmental specifications for more information.(https://www.weikunfadacai1.com/)

CompactPCI Bus Bridge: The VMICPCI-7806 is a universal CompactPCI single board computer (SBC) supporting applications as both a system slot controller or a peripheral slot controller. The PCI-to-PCI bridge interface to the CompactPCI bus is automatically configured to operate as either a transparent or non-transparent bridge. This implementation is fully compliant with PICMG 2.0 Rev 3.0, PICMG 2.1 Rev 2.0, and PCI-to-PCI Bridge Architecture Rev 1.1.

 

 

IPMI: The VMICPCI-7806 provides PICMG 2.9 Rev 1.5 IPMI support via the Zircon PM Peripheral Management Controller.

High Availability Hot Swap: The VMICPCI-7806 complies with PICMG 2.1 Rev 2.0 standard for CompactPCI hot swap. The VMICPCI-7806 complies with the high availability provisions of this standard. The processor may be removed and replaced while the system is operational. Processing can automatically be switched to a backup SBC that was previously installed in the system

CMOS Battery: The VMICPCI-7806 uses a holder that permits field replacement of the CMOS battery. A header and jumper allows the battery to be disconnected from the circuitry for long-term storage.

　Back Panel Configuration: The VMICPCI-7806 provides support for several peripherals using the CompactPCI backplane connectors. These signals are routed to the CompactPCI J3 and J5 connectors. This permits connection of the external IDE disk drive, floppy drive, USB, SATA, video, and keyboard and mouse via the VMIACC-0584 backplane adapter. Connection to these signals is provided to facilitate application development. NOTE: If the VMICPCI-7806 is not used with the VMIACC-0584 back plane adaptor, the user is responsible for either terminating video, SATA and USB or for disabling these features in the CMOS setup.

 

 

Power Requirements: Low Power/Extended Temperature option Pentium M 1.4 GHz (1 Gbyte Memory) +5VDC (+5, -3 percent), 1.5A (typical), 3.5A (maximum) +3.3VDC (+5, -3 percent), 1.5A (typical), 1.8A (maximum) +12.0VDC (+5, -3 percent), 50 mA maximum -12VDC (+5, -3 percent), 50 mA maximum Pentium M Processor (1 Gbyte Memory) +5VDC (+5, -3 percent), 4.5A (typical), 6.75A maximum +3.3VDC (+5, -3 percent), 1.5A (typical), 2.0A maximum +12.0VDC (+5, -3 percent), 50mA maximum -12VDC (+5, -3 percent), 50mA maximum Airflow: Forced air cooling required, 400 LFM minimum, measured at the top (outlet) of the unit

 

 

Altitude: Operating, 0 – 10,000 ft (3,000 m) Storage, 0 – 40,000 ft (12,000 m)

Temperature: Operating, -0° C to +50° C Storage, -20° C to +70° C

NOTE: The Pentium M processor will throttle when its junction temperature is between 90° C and 100° C. If application cannot take throttling of the CPU, then the thermal profile of the system must be verified to keep the CPU junction temperature less than 90°C.(https://www.weikunfadacai1.com/)

Humidity: Operating, Relative Humidity 5% to 95%, noncondensing Storage, Relative Humidity 5% to 95%, noncondensing

Vibration: 6 Gs RMS (20 – 2000 Hz) random, .0185 G2 per Hz spectrum

Shock: 10 Gs, 16 ms half sine, 6 axis, 10 pulses each

MTBF: Total hours 246,953

　　Operating System and Software Support

The VMICPCI-7806 supports a variety of operating systems including Microsoft® Windows 2000, Windows XP, QNX, Linux and VxWorks.

　　Physical/Environmental Specifications

Dimensions: 6U (4HP) single slot Eurocard form factor Height 9.2 in. (233.4mm) Depth 6.3 in. (160mm) Thickness 0.8 in. (20.3mm)

Model recommendation:

VMIC320-250236 GE