Description

Brand: Rexroth

Model: HDS03.2-W075N-HS12-01-FW MPN: HDS03.2-W075N-HS12-01-FW Description: 1PC Rexroth HDS03.2-W075N-HS12-01-FW Servo Drive HDS Series Input 530-670 VDC 37 AMP Output 500 VAC 40 AMP 1000 HZ New Box FedEx/DHL/UPS comes with a one-year warranty Type: Servo Drive Conditions: New Rexroth, Indramat, Bosch’s HDS03.2-W075N-HS12-01-FW is a drive controller in the HDS series. HDS03.2-W075N-HS12-01-FW has an internal air cooling type (with built-in blower) and a rated current of 75 A. The version of this controller is 2 and comes with the DIAX04 controller series. HDS03.2-W075N-HS12-01-FW servo controller is manufactured by Rexroth Indramat Bosch. The controller is cooled by an internal blower and has a rated current of 75A. This HDS controller is not equipped with command communication, and the controller series is DIAX04.

 

　　Product Description

Bosch Rexroth not only focuses on building their driver controllers, but also creates configuration and functional manuals so that their customers can fully utilize and understand them. It is precisely because they strive to make people aware of their drive controllers that HDS03.2-W075N-HS12-01-FW drive controllers become an excellent product choice for your automation system. This specific model has all the similarities with HDS03.2-W075N-HS11-01-FW, except for some differences in their configuration numbers. HDS03.2- W075N-HS12-01-FW uses a SERCOS interface with a rated current of 75 A to access its command communication. It also uses firmware typically ordered as a separate entity from the drive controller itself. In addition, HDS03.2-W075N-HS12-01-FW uses X3 and X6 connectors without mounting plates or shielded connecting cables, as well as a small hose clamp and a large hose clamp.

The warnings generated by this drive can be divided into two categories based on whether the drive performs automatic response when the warning occurs. In addition, in cases where normal operation is no longer allowed, error messages may be generated, in which case the drive will shut down on its own until the error message is cleared or the 0-1 edge bits are enabled by the input controller. HDS03.2-W075N-HS12-01-FW also uses an analog interface that can automatically switch to working mode when the control voltage is turned on. In addition, in order to configure the motor for this drive, the motor characteristic parameters (including peak current, maximum speed, etc.) must be input through the DRIVE TOP software using data from the motor database.

Wake Industrial offers a one-year warranty for HDS03.2-W075N-HS12-01-FW, which can be shipped to any address worldwide. Once the ready to operate contact “Bb” is closed, the drive controller is ready to receive power. Once the power supply voltage is connected and all monitoring functions are normal, the contact “Bb” closes and sends a signal indicating that they are running. Contact “Bb” can be evaluated, such as in the control system, so that if a unit has a hardware defect, please identify which controller in the driver package has failed. Circuit load: DC 24 V, 1 A (maximum=continuous) Contact minimum load: 10 mA Note: The direct connection of the main contactor through contact Bb is only allowed when the connecting current does not exceed 1A. Higher current can cause relay failure. Due to these aging conditions, it is not recommended to use protective circuits for rheostats. This can lead to early failures of connected components and therefore also include the unit itself. Starting lock AS+, AS -, ASQ is a safety mechanism used to prevent ASQ company from accidentally starting the connected motor in the event of an error. It is used to safely shut down independent working areas or plants within the machine. Note: Starting the lock will not make the moving axis stationary. The supplementary information about startup locking has been summarized in the description “Startup locking function in DDS drive controller” DOK-DIAX02-DDS * ANL * FKT-AWXX-EN-P.

 

　　Popular model recommendations:

BGR DKC02.3-LK SCK02/01